Reimplement nFAPI message exchange between L1 and L2 following the
changes in parent commit removing msgDataTx.
Avoid direct calls and use NR_IF_module fptrs to avoid linking problems.
allowing to remove some function definitions that are not needed.
Note: after this commit, monolithic works but nFAPI operation is broken
and fixed in the next commit, to keep the changes small(er). All
simulators work.
This commit removes the use of msgDataTx's intermediate buffers for FAPI
messages and the call of the "Schedule response". The latter incurs an
additional copy of FAPI messages for the TX chain (for the RX chain, it
is and will remain there) which we can avoid.
Instead, it uses an NR_Sched_Rsp_t-typed variable sched_response to
store the results of the scheduler when called from tx_func(). Thus, the
scheduler remains unchanged (it gets a pointer to where to put FAPI
messages), but we don't call nr_schedule_response() to then copy FAPI
messages into the L1, but have them in a local variable sched_response.
sched_response on on the data segment, as it is big and would overflow
the stack; at the same time, this is ok because only one tx_func() runs
at a time.
Since we don't use allocate_sched_response() anymore, we don't need
deref_sched_response().
clear_slot_beamid() is moved to tx_func(), as it was called in
nr_schedule_response().
Since the "intermediate" NR_gNB_DLSCH_t structure groups both the
DL_tti_pdsch and TX_data.req structures, a pointer has been created to
point to pdsch_pdu. This affects a number of simulators, as they have to
put some messages on the stack:
- nr_dlschsim: put the corresponding variable on the stack
- nr_pbchsim: a new array for the SSB PDUs has been introduced
Further, these changes are now necessary:
- nr_dlsim: there were variables "rel15" and "pdsch_pdu_rel15" that
point to the same PDSCH PDU. At least "rel15" would not exist, as the
corresponding pointer is now populated in phy_procedures_gNB_TX(), and
we therefore refer to the single PDSCH PDU variable with
"pdsch_pdu_rel15", but at the place where "rel15" used to be
initialized.
- nr_ulsim: use nr_save_ul_tti_req() to load PDUs into the RX chain
instead of nr_schedule_response(), which does not exist anymore.
The next commit will remove msgDataTx. We can therefore not use
msgDataTx to retain the PDSCH/DLSCH variables, and move them to the gNB.
Note that the only reason for NR_gNB_DLSCH_t after this commit is to
hold various large buffers (c, b, f). Future work could be done to
remove this, in which case the array inside PHY_VARS_gNB could be
deleted.
On this occasion, clean up the use of init_DLSCH_struct() and
reset_DLSCH_struct() (renamed destroy_DLSCH_struct()) and centralize
their call in phy_init_nr_gNB()/phy_free_nr_gNB(), and correct
simulators accordingly.
There is no point in tracking the "active" state: the SSB PDU will be
sent from MAC to L1, encoded, and then "discarded" (by marking the
number of SSB PDUs as 0). Hence, remove this intermediate type.
Refactor DLSCH scheduler
Refactor the DLSCH post processor similarly to what has been done in
!3521 with the goal of saving an additional iteration through all UEs,
hopefully making the DLSCH scheduler faster.
It further includes changes to make working with and debugging multi-UE
operation easier:
- add some measurements in L1 (for total TX/RX time)
- a new option MACRLCs.[0].stats_max_ue to limit the number of UEs in
the periodic output (default: 8, 0=disable)
- avoid stack overflow in the MAC
- fix the writing of stats to nrMAC_stats.log and nrL1_stats.log when
the written output reduces by truncating the files
- avoid to schedule retransmission with 0 RBs.
Refactor PRACH handling at the gNB
- Remove race conditions by correctly setting mutexes
- Fix a bug when having multiple RACH occasions
- Reduce memory footprint by removing global memory, which should also
fix potential memory data races in FHI 7.2
- Additional fixes, see commit messages
saves about 600MB of memory allocation
Move the definition of PRACH items and the PRACH list to the
defs_nr_commons.h file.
Do not re-write the entire structure in nr_schedule_rx_prach(), as it is
quite large now.
The function rx_nr_prach become autonomous, it doesn't read anymore global variables
So, it can become (later) a threadpool work, that will send a message when it finishes
rx_nr_prach_ru() still use some global variables, but it is executed in sequence, inside the ru main loop, that limits the probability of race conditions
Note that this strdup has been intentioally created for debugging
purposes in core files.
See also: 1ab3b8dd8e ("add version signature in core files...")
Refactor SDAP adaptation work for QoS
This MR is an adaptation of the code introduced in !2703.
The goal is a cleanup and functional refactor of the SDAP/PDCP
integration, that is:
- centralize SDAP configuration logic
- simplify entity creation
- improve robustness of role-based SDAP handling
- prepare the codebase for clean support of DRB reconfiguration and
teardown flows
More concretely:
1. New sdap_config_t and get_sdap_Config()
- Introduced an internal struct sdap_config_t to abstract SDAP config
input
- Centralized SDAP config parsing into new get_sdap_Config() function
that translates ASN.1 NR_SDAP_Config into this internal
representation. This is called during RRC triggered
(re)configuration procedures.
- Enable mapping of number of QoS flows > 1
2. Unified role handling with bitmasks
- Added a bitmask-based entity_role field to track SDAP directions:
SDAP_UL_RX, SDAP_UL_TX, SDAP_DL_RX, SDAP_DL_TX: header presence was
determined by simple direction (UE vs gNB) and individual
is_sdap_rx/tx() checks, however nr_sdap_rx_entity behaves
differently depending on the direction of the RX entity (DL/UL),
therefore this change can help enable a more accurate SDAP header
handling across directions and node types.
- Replaces old helpers is_sdap_rx() / is_sdap_tx() with internal
checks against the role bitfield
- QFI-to-DRB mapping is now annotated with direction for both data and
control PDUs
3. Simplified DRB and SDAP setup
- add_drb() in PDCP API now delegates SDAP config processing cleanly
- new_nr_sdap_entity() is used consistently to register a fresh SDAP
context for the UE and PDU session.
- Also, re-use and reconfigure existing SDAP entity if already
exists.
- logging has been added to trace mapped QFIs from RRC and resulting
table entries
4. Improved QFI-to-DRB management
- Refactored nr_sdap_qfi2drb_map_update() to register QFIs based on
parsed config
- Ensures control PDUs are correctly routed even after reconfiguration
- Extended nr_sdap_ue_qfi2drb_config: perform UL QoS flow to DRB
mapping configuration for a SDAP entity has already been established
according to TS 37.324, 5.3 QoS flow to DRB Mapping, 5.3.1
Configuration Procedures. Handle both UL QoS Flows mapping rules to
add and to remove. QFIs will now be properly unmapped if specified
via mappedQoS_FlowsToRelease, this might prevent stale QFI mappings
from being used incorrectly.
- nr_sdap_qfi2drb() and sdap_map_ctrl_pdu() now strictly fallback to
default_drb only if a QFI mapping is missing. Missing default DRB
now triggers LOG_E() (previously silent or misrouted to DRB 0).
5. Other cleanup
- Remove dependencies from legacy rb_id_t
- Remove rb_id parameter from nr_sdap_tx_entity() function signature
- Update tx_entity function pointer
- Remove rb_id parameter from sdap_data_req() function signature
- Remove unused rb_id variable from sdap_tun_read_thread
The rb_id parameter was redundant since SDAP determines DRB ID
from QFI mapping via entity->qfi2drb_map(entity, qfi). This
simplifies the interface.
fix direct bugs of not used RU_RX_SLOT_DEPTH defined constant
with this commit, the gNB can work if we change RU_RX_SLOT_DEPTH to
another value than 4 but it remain not well designed
UE symbol based PDCCH receiver
This is a partial rebase/rewrite of !2895
The goal of this MR is to check how we can merge this.
The eventual result is stated in !2895. The way forward is to modify UE
RX procedures to work symbol by symbol by extracting the symbol loop out
of RX procedures. After all channels are modified this way, the main
thread can be modified to work symbol by symbol.
At this point only PDCCH was modified.
This implements the STOP.request/indication for all 3 transport mechanisms, the VNF will send the STOP.request to the PNF, indicating it will disconnect, and await a STOP.indication from the PNF
The WLS VNF is reworked to be able to start before the PNF, by calling call rte_eal_init and rte_dev_probe to determine if dpdk has been initialized properly, before calling rte_eal_init in the intended process when it is appropriate to do so
1.Create new funtion nr_symbol_fep() to do OFDM demod of one symbol on
all antennas. This is called by nr_slot_fep() for now. In the
upcoming MR, this function will be called directly after reading
each OFDM symbol from the radio.
2.Removed redundant memory alignment. DFT function performs memory
alignment if the input memory is not aligned.
Support beam index in OAI 7.2 Fronthaul Interface
This branch supports beam index in OAI 7.2 Fronthaul Interface.
- For CP DL (PDSCH), nBeamIndex of the corresponding prbMapElm is set
when sending IQ data in oran_fh_if4p5_south_out. nBeamIndex of the
corresponding prbMapElm is set when sending IQ data in
oran_fh_if4p5_south_out.
- For CP UL (PUSCH and PRACH), nBeamIndex of the corresponding prbMapElm
is set in oran_fh_if4p5_south_out.
In addition, it fixes a couple of issues
- XRAN hardcodes nBeamIndex of PRACH to zero. Modify XRAN to support
setting of nBeamIndex of PRACH and update xran F release patch.
- Fix the bug in calculating fh_config->neAxc where num_beams_period is
multiplified twice
Testing methodology: Use Benetel O_RU for testing even though it does
not support beamforming. With successful registration and data transfer,
one could check the pcap on the fronthaul interface to see if CP packets
are with the right beam index.
Results:
1. Verified that CP-packets for SSB, DCI, PDSCH, PRACH, PDSCH, PUSCH,
CSI-RS and SRS are with the right beam index
2. Verified that there is no side-effect on Benetel O_RU. UE could
register properly.
3. Verified 4 SSB with ssb_PositionsInBurst_Bitmap = 85. Could see SSB
and PRACH with 4 different indices.
RFSim test for 10 UEs/process
This MR adds a testcase and changes required to run 10 UEs in a single
process with RFSim
- Added deregistration for all connected UEs
- Refactored MAC/RRC instance handling
- made map_current_symbol thread safe
- made opeanir0_cfg thread safe and local
- Added 10UE/process testcase
- Replaced ITTI message queues with notifiedFIFO for RRC to MAC communication in UE.
- Enables correct message delivery to multiple MAC instances running in parallel threads.
- Introduced `nr_mac_rrc_message_t` union for MAC-RRC messages.
- Updated all relevant message handling and initialization code to use notifiedFIFO.
- Use MAX_NUM_NR_UE_INST in NR UE MAC to control number of MAC instances.
- Modify the MAC interface slightly so that nr_l2_init_ue only initializes one instance
Use MAX_NUM_NR_UE_INST for number of NR UE RRC instances. Change the RRC
interface slightly so nr_rrc_init_ue initializes only one RRC instance pointed
to by the id given to the function
RF emulator and improvements of the timers
RF emulator:
Add an RF library emulating a real device without the need of a real
device. This is thought to enable using phy-test without requiring a
radio device or channel simulation. The library synchronizes on the
real time clock, drops TX and generate noise on RX. Noise generation
can be disabled and the noise level configured.
Timers improvements:
- Fix standard deviation for merged timers
- Add display of ULSCH decoding timers
- Add decoding timer in AAL
