Ubuntu 20 is EOL [1] unless people pay for support. Therefore, remove it
from build_helper. People can still use it, but might need to install a
more recent cmake version (which the next commit will upgrade). The rest
should be the same.
[1] https://ubuntu.com/about/release-cycle
Prior to this commit, constants NB_ANTENNAS_RX/TX are provided on the
command line to each compiler invocation. This has the drawback (1) that
also files that don't need that get the constants, and (2) it is not
easy to find them using ctags or similar, as the only definition is in
CMakeLists.txt (where it is not found).
In this commit, use cmake configure_file() to write a header file with
these constants. The file will be generated during cmake invocation, and
written to <build-dir>/common/cmake_defs.h. The relevant files that
need this definition will pick it from the header.
This has been used previously also in a commit to write git information.
See-also: 8bffd1666d ("Avoid complete rebuild on cmake run with git info change")
[FHI72] Remove support for xran E release
All the use cases we tested with E release are working end-to-end with F release.
The near future plan is to support K release which is ongoing in the MR !3444.
All the use cases we tested so far, are supported with xran F release.
Therefore, we can proceed with removing the support with E release.
In addition, our plan is to bring the support for K release which is ongoing activity in
the MR https://gitlab.eurecom.fr/oai/openairinterface5g/-/merge_requests/3444.
There is no reason to not allow
./build_oai -I -w USRP -w BLADERF
To install USRP and BladeRF together (which will be used in the CI in a
later commit). Fix this.
Add fallbacks for ARMv8a to make it compile
The current code, on ARM, uses ARMv8.1-A RDM instructions. Add a
fallback for processors that do not have this instruction set.
Add some specific compile options for this platform.
Add debian 12 to the list of architectures.
In xRAN, it appears that T1a/Ta4 values are assumed to be within a TTI.
When T1a/Ta4 values with larger than a TTI are used, this causes two issues: (1) C-plane packets to be generated later than expected and (2) oai_xran_fh_rx_callback() receives the wrong timing information resulting in potentially empty/stale PUSCH/PRACH data to be read.
In this patch, we modify xRAN to make it handle large T1a/Ta4 values properly.
The changes include: (1) three additional variables in offset_num_slots_* (xran_dev.h), (2) modify "xran_timing_create_cbs" and "xran_timer_arm_for_deadline" (xran_cb_proc.c), and (3) revise "tx_cp_dl_cb" and "tx_cp_ul_cb" (xran_main.c).
Additionally, we add additional guard conditions to prevent xran_tx_proc.c from sending U-plane packets when it is not a downlink slot.
[FHI72] [xran F] Handle fragmented (un)compressed packets
In both E and F, the radio-transport fragmentation is not supported, and
all the "fragmented" (not seen as fragments in the xran, only as
sections) packets contain "E-bit" equal to 1. Per spec, the value 1 for
"E-bit" signifies the last fragment of one symbol. For more info, please
see "ecpriSeqid" section in the spec.
In E:
- nRBStart and nRBSize is updated according to the sent/received packet;
- max sections = 1;
- when a packet is fragmented, the xran uses memcpy(pos, iq_data_start,
size) function, and nothing is stored in start_prbu , num_prbu ,...
In F:
- nRBStart and nRBSize is only used for C-plane messages;
- nPrbElm represents the number of sections for DL only;
- based on the nPrbElm, each section contains UP_nRBStart and UP_nRBSize
parameters which represent the start and number of PRBs in one section
or one fragment;
- when a packet is fragmented, the xran uses nSecDesc and sec_desc to
extract the packet section content, and the data is stored in
start_prbu , num_prbu ,...
Previous work on the fragmentation in F:
- #884
- !3394 - only increases the XRAN_MAX_FRAGMENT from 4 to 6, since it was
only tested with BFP 8, but not end-to-end unfortunately. But this MR
fixes all the issues.
Tested with VVDN RU, 2x2, 16 bits, 100MHz, 30kHz, MTU <= 9216 B, and
Quectel UE RM520N-GL Revision: RM520NGLAAR03A03M4G.
The sufficient number of fragments needed for MTU 1500 and 8b compression is 6.
However, XRAN_MAX_FRAGMENT must be incremented by one (6+1 = 7).
In the MR https://gitlab.eurecom.fr/oai/openairinterface5g/-/merge_requests/3394, XRAN_MAX_FRAGMENT was increased to 6,
but the Tx data was actually copied 5 times, and unfortunately I haven't tested end-to-end back then.
This commit was successfully tested with Liteon FR1.
Create Debian and Redhat packages with CPack
Use CPack in CMakelists in order to create packages, creation command is
available in build_oai script and options description is available in
packages.md
Support beam index for LiteON FR2 RU that needs per symbol section in CP packets
This branch supports beam index for LiteOn FR2 RU and others. It adds
the support of beam index for LiteOn RU that uses per-symbol CP packet
and is a sequel of MR !3605 (merged) that supports beam index for RU
that uses per-slot CP packets.
A. To support LiteOn FR2 RU, the following are needed.
a. Per symbol beamforming. Need separate section for each symbol on CP packet.
b. Handle these two bugs:
- section ID on UP packet is set wrongly to 13 for all sections
- prach eAxC offset starts from 0 instead of from last antenna port
number used by other channels.
B. Implementation
a. set fh_config->RunSlotPrbMapBySymbolEnable based on the setting in the configuration file
- if disable, the existing per-slot scheme is run on xran.
- if enable, RunSlotPrbMapBySymbolEnable mode is on in xran so that xran
will generate PrbElm per symbol (aka total of 14)and perform
per-symbol processing on the corresponding PrbElm.
b. set fh_config->LiteOnIgnoreUPSectionIdEnable based on the setting in
the configuration file if enable, handle 2 "features" of Liteon:
- To handle the section_id = 13 issue on Liteon where section ID is set
wrongly to 13 for all sections
- To handle the prach eAxC offset issue on Liteon where it starts from 0
instead of from the end of last antenna port number
c. if fh_config->RunSlotPrbMapBySymbolEnable, OAI FHI
- invoke xran_fh_rx_read_slot_BySymbol() instead of xran_fh_rx_read_slot()
- invoke xran_fh_tx_send_slot_BySymbol() instead of xran_fh_tx_send_slot()
C. Testing
a. Command to test benetel RU
sudo LD_LIBRARY_PATH=.:$DPDK_INST/lib/x86_64-linux-gnu/ ./nr-softmodem -O /etc/ran_development/CONFs/gnb.sa.band77.273prb.fhi72.4x4-benetel550_c0.conf --thread-pool 21,22,23,24,25,26,27,28
Results:
iperf UDP uplink
[ 5] 0.00-10.22 sec 87.3 MBytes 71.6 Mbits/sec 0.100 ms 370/63081 (0.59%) receiver
iperf UDP downlink
[ 5] 0.00-10.00 sec 796 MBytes 668 Mbits/sec 0.017 ms 1824/586404 (0.31%) receiver
b. Command to test LiteOn FR2 RU
sudo LD_LIBRARY_PATH=.:$DPDK_INST/lib/x86_64-linux-gnu/ ./nr-softmodem -O /etc/ran_development/CONFs/gnb.sa.band78.66prb.fhi72.2x2-liteon-F-Release.conf--thread-pool 21,22,23,24,25,26,27,28
Result:
iperf UDP uplink
[ 5] 0.00-10.20 sec 89.9 MBytes 73.9 Mbits/sec 0.156 ms 212/64848 (0.33%) receiver
iperf UDP downlink
[ 5] 0.00-10.00 sec 361 MBytes 303 Mbits/sec 0.077 ms 277662/542891 (51%) receiver
D. Difference between LiteOn FR2 E release configuration file and that for F release is
diff gnb.sa.band78.66prb.fhi72.2x2-liteon-KB.conf gnb.sa.band78.66prb.fhi72.2x2-liteon-F-Release.conf 39d38
< beam_weights = [1, 1];
225a225
> beam_weights = [1];
312c312,313
< mtu = 1500; # check if xran uses this properly
---
> #mtu = 1500; # check if xran uses this properly
> mtu = 9000; # check if xran uses this properly
313a315,316
> RunSlotPrbMapBySymbol = 1;
> LiteOnIgnoreUPSectionId = 1;
Add the F patch that work on both Benetel and LiteOn RU. support
fh_config parameters RunSlotPrbMapBySymbol and LiteOnIgnoreUPSectionId.
Change version number.
These files are not used anywhere. The only remaining cmake find files
are:
- findarmral and findxran: used by FHI7.2 driver
- findsctp: used by top-level CMakeLists.txt
- findgnutls: NOT actually used but GnuTLS is a dependency of websrv, so
I leave it for the moment (should be removed if the webserver is
removed)
Signed-off-by: Robert Schmidt <robert.schmidt@openairinterface.org>
There is no HSS/MME in this repository, which is the majority of this
file. Remove it, since it is outdated.
Signed-off-by: Robert Schmidt <robert.schmidt@openairinterface.org>
Setup routes was added by the author of FlexRAN. The UEs always set up
routes automatically, and this file is therefore not needed.
See-also: 287c182925 ("Remove FlexRAN")
Signed-off-by: Robert Schmidt <robert.schmidt@openairinterface.org>
Implementation of STOP exchange
This implements the STOP.request/indication for all 3 transport mechanisms, the
VNF will send the STOP.request to the PNF, indicating it will disconnect, and
await a STOP.indication from the PNF
The WLS VNF is reworked to be able to start before the PNF, by calling call
rte_eal_init and rte_dev_probe to determine if dpdk has been initialized
properly, before calling rte_eal_init in the intended process when it is
appropriate to do so
Support beam index in OAI 7.2 Fronthaul Interface
This branch supports beam index in OAI 7.2 Fronthaul Interface.
- For CP DL (PDSCH), nBeamIndex of the corresponding prbMapElm is set
when sending IQ data in oran_fh_if4p5_south_out. nBeamIndex of the
corresponding prbMapElm is set when sending IQ data in
oran_fh_if4p5_south_out.
- For CP UL (PUSCH and PRACH), nBeamIndex of the corresponding prbMapElm
is set in oran_fh_if4p5_south_out.
In addition, it fixes a couple of issues
- XRAN hardcodes nBeamIndex of PRACH to zero. Modify XRAN to support
setting of nBeamIndex of PRACH and update xran F release patch.
- Fix the bug in calculating fh_config->neAxc where num_beams_period is
multiplified twice
Testing methodology: Use Benetel O_RU for testing even though it does
not support beamforming. With successful registration and data transfer,
one could check the pcap on the fronthaul interface to see if CP packets
are with the right beam index.
Results:
1. Verified that CP-packets for SSB, DCI, PDSCH, PRACH, PDSCH, PUSCH,
CSI-RS and SRS are with the right beam index
2. Verified that there is no side-effect on Benetel O_RU. UE could
register properly.
3. Verified 4 SSB with ssb_PositionsInBurst_Bitmap = 85. Could see SSB
and PRACH with 4 different indices.
RF emulator and improvements of the timers
RF emulator:
Add an RF library emulating a real device without the need of a real
device. This is thought to enable using phy-test without requiring a
radio device or channel simulation. The library synchronizes on the
real time clock, drops TX and generate noise on RX. Noise generation
can be disabled and the noise level configured.
Timers improvements:
- Fix standard deviation for merged timers
- Add display of ULSCH decoding timers
- Add decoding timer in AAL
Add a simple RF emulator library with no real RF.
It only synchronizes the gNB with the real time clock.
It is to be used for stress test or benchmarking in phy-test mode.
Improve MAC docs for MCS and docker for BuildKit usage
See commits for details. The first one is for fixing an omission in
!3281, the second to clarify docker build usage.
Closes: #973
CI: speed up and simplify build, remove unnecessary Python code, remove --eNB* parameter list
This cleans up the CI framework for running end-to-end tests, and
improves the integration with OAI code. Specifically
- cleanup build_oai and helpers to output all text, which is captured
better by the CI
- build some images in the Cluster-Build in parallel to increase speed
- remove all --eNB{,1,2}{IPAddress,UserName,Password} variables. Those
were indexed through "instance" and "server ID" and are replaced with
the actual node name. I consider further cleanup to introduce a
"global" XML file node name so we don't need this in each step and
instead define this once.
- individual cleanup
build_oai primarily builds UHD for OAI. Thus, a number of targets (B100,
USRP1/2, ...) can be omitted, as OAI does not run on them. Further,
disable documentation and man pages, which is typically not necessary
for the averages user, and does not need to be installed for containers.
Similarly to the parent, don't redirect log files to a file. It makes
the CI more complicated, and also raises user awareness of what is being
installed.
Libboost went from 1.74.0 to 1.83.0 alongside Ubuntu update.
GCC version is set as default to be more practical.
In Ubuntu22, apt sources were in .list files, in Ubuntu24 they are in .sources files.
Add --break-system-packages for pip installation to use same logic as before, see the pip update 23.0.1 (2023-02-17).
With Ubuntu24 liboai_device requires libpython3.12
Redirecting to a file has the problem that it is difficult in the CI to
recover these files. Furthermore, at least with ninja, when running
build_oai interactively, the build output will only take some lines
(because ninja rewrites lines), so the change should not be that big to
users.
One CI function would print the entire output from build_oai to the
console. Since that output might be long now, do not do this. The file
is archived, anyway.
LDPC BBDEV/AAL rework
This branch aims to generalize the existing LDPC T2 implementation to support
other DPDK BBDEV accelerators, e.g., Intel ACC100/200.
Differences from the current T2 implementation include:
1. relax CMakeLists.txt checking for custom dpdk-t2 implementation,
technically, any DPDK BBDEV should work
2. BBDEV capability checks during init
3. llr_scaling to scale the input llr accordingly for better decoding
performance on the Intel ACC100/200
4. self-managed harq buffers for the ACC200, as internal harq memory is not
available
Tested BBDEV devices:
1. Intel ACC100
2. Intel ACC200/VRB1
