When the gNB answers RRCReestablishmentRequest with RRCSetup (TS 38.331
clause 5.3.3.4 fallback), the UE must release all bearers except SRB0 before
applying the new masterCellGroup. CONFIG_RESET was queued after RLC release,
so the MAC slot thread kept polling LCID 1 from a stale lc_ordered_list while
the RLC entity was already NULL.
Queue NR_MAC_RRC_CONFIG_RESET (RRC_SETUP_REESTAB_RESUME) first, then release
PDCP, RLC, and SDAP. On the MAC thread, clear lc_ordered_list except SRB0
before release_mac_configuration() so the UL scheduler stops looping released
logical channels until CONFIG_CG re-adds SRB1.
Changes:
- rrc_UE.c: move CONFIG_RESET to the start of nr_rrc_rrcsetup_fallback()
- config_ue.c: drop non-SRB0 lc_ordered_list entries on RRC_SETUP_REESTAB_RESUME
Closes: #128
Signed-off-by: Guido Casati <guido.casati@openairinterface.org>
Keep normal no-redirection RRCRelease on the acquired
camped-cell context while preserving the existing full
GO_TO_IDLE cell-selection path for other idle transitions.
Changes:
- Add UE_IDLE and GO_TO_IDLE_KEEP_CAMPED to represent camped
idle without starting RA.
- Map no-redirection RRCRelease to GO_TO_IDLE_KEEP_CAMPED and
keep SIB1 validity for that path.
- Release connected-mode MAC/BWP0 dedicated config while
preserving common BWP0 and paging PDCCH context.
- Keep the existing full GO_TO_IDLE cleanup for idle transitions
that must perform cell selection.
Refs:
- TS 38.331 §5.3.11
- TS 38.304 §5.2.5, §5.2.6, §7.1
- TS 38.321 §5.12
Signed-off-by: Guido Casati <guido.casati@openairinterface.org>
RRC starts random access via NR_MAC_RRC_START_RA with an explicit
cause. RA trigger is no longer piggybacked on NR_MAC_RRC_CONFIG_RESET.
T300 expiry and RRC re-establishment are the call sites switched in this
commit. MAC handles setup/T300 and re-establishment paths in
nr_mac_start_ra().
Changes:
- Add nr_mac_rrc_types.h (nr_mac_ra_start_cause_t)
- Add nr_mac_rrc_start_ra_t in rrc_messages_types.h
- In rrc_UE.c, add nr_rrc_trigger_mac_ra(), call it from
handle_t300_expiry and nr_rrc_initiate_rrcReestablishment
- In config_ue.c:
- add nr_mac_start_ra() entry point with causes switch
- add nr_rrc_mac_start_ra() handler
- remove T300_EXPIRY, RE_ESTABLISHMENT reset handling
in nr_rrc_mac_config_req_reset, now delegated to
nr_mac_start_ra
- mac_defs.h: drop T300_EXPIRY from NR_UE_MAC_reset_cause_t
Signed-off-by: Guido Casati <guido.casati@openairinterface.org>
Push the 5G-S-TMSI received by UE RRC down to MAC so paging can use
the TS 38.304 UE_ID.
Changes:
- add a paging UE_ID field to the UE MAC paging configuration
- add nr_rrc_mac_config_req_paging_ue_id() to derive UE_ID from
5G-S-TMSI and store it under the MAC interface mutex
- update the NAS_5GMM_IND handling in rrc_nrue() to pass the received
5G-S-TMSI to MAC for paging PF/PO derivation
Signed-off-by: Guido Casati <guido.casati@openairinterface.org>
Populate UE MAC paging state from SIB1 PCCH-Config so PF/PO-related
parameters are available to the rest of the UE MAC.
Changes:
- Add nr_ue_paging_cfg_t to NR_UE_MAC_INST_s with parsed paging fields
(T, N, Ns, PF_offset, X) and the optional
firstPDCCH-MonitoringOccasionOfPO list (first_mo_of_po[],
first_mo_of_po_count)
- Add configure_pcch_config() to decode SIB1 PCCH-Config via the
common helpers nr_pcch_default_paging_cycle_rf,
nr_pcch_n_and_paging_frame_offset, nr_pcch_ns_per_pf and
nr_pcch_first_pdcch_start_mo
- Add NR_PCCH_MAX_PO constant (TS 38.331 PCCH-Config) and size the
first_mo_of_po[]
- Invoke configure_pcch_config() from nr_rrc_mac_config_req_sib1()
Signed-off-by: Guido Casati <guido.casati@openairinterface.org>
at RRC we don't store CSI-MeasConfig information so in some scenarios (see #1063) we may not have the full pictures to understand if what RRC received is a valid configuration
we verify at L2 instead after updating CSI-MeasConfig and if it fails we send a message to RRC
- all RAN code, CI code, configuration files, dockerfiles, in CSSL v1.0
- all deployment code (openshift, charts, ancillary files like shell
scripts), in MIT
- documentation in CC-BY-4.0
- exceptions might apply and are listed in NOTICE
- there is a new LICENSES folder with all licenses
- CONTRIBUTIONS.md has been updated accordingly
For automated changes based on OAI PL v1.1:
perl -i~ -0pe 's/\/\*.*Licensed to the OpenAirInterface.*openairinterface.org\n#?/\/*\n * SPDX-License-Identifier: LicenseRef-CSSL-1.0\n/s' **/*.{c,h,cpp}
perl -i~ -0pe 's/\/\*.*Licensed to the OpenAirInterface.*openairinterface.org\n#?/\/*\n * SPDX-License-Identifier: LicenseRef-CSSL-1.0\n/s' **/*.ts
perl -i~ -0pe 's/<!--.*Licensed to the OpenAirInterface.*openairinterface.org\n.*-->/<!-- SPDX-License-Identifier: LicenseRef-CSSL-1.0 -->/s' **/*.xml
The rest (cmake, files with missing license, cmake) manually.
Remove the \file directive, as it is always superfluous because the
current file is implicit [1]:
> If the file name is omitted (i.e. the line after \file is left blank)
> then the documentation block that contains the \file command will belong
> to the file it is located in.
Author names and e-mails are not relevant for us: it can always be
inferred from git blame, and is often outdated.
Eurecom code has been contributed and was under OAI PL v1.0/v1.1.
For the cpack package contact: put generic email address that is
independent of an individual and that will remain reachable.
[1] https://www.doxygen.nl/manual/commands.html#cmdfile
Remove unused function arguments
Some of them, because there are hundreds if not thousands. Warnings at compilation time can be enabled using -Wunused-parameter.
without this fix, after sync is successful, RAR is not getting decoded.
PDCCH area also changes as SSB offset can change. if MAC configuration changes.
Actual problem is that SYNC does not happen on the target cell as frame parameters is not updated
and ssb start carrier is not correct in the UE frame parameters
function nr_get_ssb_start_sc to determine ssb_start_subcarrier
Remove L1 dependence from NR band number
L1 band information relied on get_band function that couldn't provide an
unambiguous result. Also there is no SCF compliant parameter for L1 and
generally we don't really need that information in L1.
The MR also remove a RU section that used nr_band but was never really
accessed in NR.
The k1 for PRACH calculation in config_common_ue() should be the same as in config_common_ue_sa(),
otherwise k1 is wrong when handover to target cell if msg1-FDM not 0 in reconfigurationWithSync.
NR UE: add neighboring cell measurements and measurement report of event A3
This is a rework of MR !2385 (closed), the goal is to add neighboring cell
measurements and measurement report of event A3 for NR UE.
This MR was tested with:
- 3rd-party gNB
- 2 OAI-gNB-DUs
The neighboring cell measurements and measurement report of event A3 for OAI-UE
are working as expected.
During N2 handover, the UE receives reconfigurationWithSync which correctly
sets the target cell frequency in mac->phy_config.config_req.carrier_config
via config_common_ue() call.
However, when SIB1 is decoded after reconfiguration,
nr_rrc_mac_config_req_sib1() calls config_common_ue_sa() which unconditionally
overwrites the frequency with the command-line parameter (downlink_frequency),
which corresponds to the source cell frequency.
This causes a critical issue during RRC re-establishment:
- The UE uses the wrong frequency (source cell) for key derivation (kgnb*)
- The gNB uses the correct frequency (target cell) for key derivation
- This mismatch results in different kgnb* keys on UE and gNB
- Integrity check fails: "Integrity of RRCReestablishment failed, going to IDLE"
Root cause:
config_common_ue_sa() is used for SIB1 processing (initial cell selection) and
uses ServingCellConfigCommonSIB which doesn't contain absoluteFrequencyPointA.
It must derive frequency from command-line parameters. However, after handover,
the frequency has already been correctly set by config_common_ue() (used for
reconfigurationWithSync) which uses ServingCellConfigCommon with absolute
frequency information.
Solution:
Modify config_common_ue_sa() to preserve the existing frequency if it's already
initialized (non-zero). Only set frequency from command-line parameters during
initial cell selection when dl_frequency is 0. This ensures:
- Initial cell selection: frequency derived from command-line parameter, just once
- After handover: frequency preserved from reconfigurationWithSync
- MAC maintains its own frequency state independently
The fix applies to both DL and UL frequencies to maintain consistency.
There is probably room for more refactoring to the resync flow, since
the functionalities in config_common_ue and config_common_ue_sa are
partially overlapping and upon reconfigurationWithSync some other
configurations might be applied twice.
These logs are very helpful to identify cell configuration
changes in MAC/PHY, for monitoring purposes, and to rapidly
signal integrity failures during re-establishment.
Make sure to apply Doppler and TA not directly when receiving the target cell ntn_config,
but apply Doppler just before the initial sync, and the TA after the initial sync when
we have tha actuel cell frame and slot numbers.
We need the ntn_config when reconfiguring the PHY layer for a new initial sync,
e.g. for calculating the DL Doppler frequency.
As a dedicated scheduled_response dl_config PDU it reaches the PHY layer too late,
as part of the phy_config.config_req it reaches the PHY layer in time with the
other configuration values.
Instead of trying to estimate N_UE_TA_adj with a second degree polynomial,
we introduce orbit propagation to calculate N_UE_TA_adj with higher accuracy.
When we receive the satellite ephemeris data consisting of the satellite position vector
and the satellite velocity vector, we calculate parameters for orbit propagation, assuming
a circular orbit in the plane created by the satellite position vector and the satellite
velocity vector. This is done in the function prepare_ue_sat_ta().
Every millisecond, we use these parameters together with the time since epoch to calculate
the satellite position on that orbit and from this the reound-trip-time between UE and the
satellite, what corresponds to N_UE_TA_adj. This is done in the function apply_ntn_timing_advance().
The acceleration magnitude on the orbital path can be calculated as:
t = 2 * pi * r / v
omega = 2 * pi / t = v / r
acceleration = omega² * r = v² / r
Where t is the orbital period, r is the orbital radius, v is the orbital velocity, omega is the angular velocity.
The acceleration direction is from the SAT position towards the earth center.
To calculate the acceleration towards the UE, this is projected on the direction from the SAT to the UE.
simplify and make more local variables in nr_rx_pdcch() and fix small bugs...
simplify and make more local variables in nr_rx_pdcch() and fix small bugs
(size 9 RE instaed of 12 RE)
TS 38.213 4.1 says coreset 0 is present only if kssb < 24 for FR1 and <
12 for FR2. This commit sets get_sib1 flag based on kssb.
Also, setting of mac state is taken out of function nr_ue_decode_mib().
continuously update SIB19 information for rfsim NTN LEO scenarios
Contains mainly these changes:
- gNB: add function nr_update_sib19() allowing to update SIB19
information
- rfsimulator: update SIB19 contents every frame for LEO channel
simulations
- NR UE: improve initial timing advance calculation from SIB19
Before, we only considered ta_Common_r17 and the SAT position from SIB19
to compute the initial timing advance value. This is good enough if the
satellite does not move too fast (e.g. GEO satellite).
Now we also consider ta_CommonDrift_r17, ta_CommonDriftVariant_r17 and
the SAT velocity together with the epoch time from SIB19. This improves
the accuracy of the initial TA computation, esp. for LEO satellite
scenarios.
